歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-新聞資訊

新聞資訊

超聲波清洗設備的振子需要注意的細節有哪些？

作者：admin來源：http://www.zhuohengsh.com/時間：2022-01-26

超聲波清洗設備顧名思義就是利用超聲波進行工作的清洗設備，而超聲波中振子對清洗效果是非常重要，所以小編就想給大家講解下安裝超聲波清洗設備的振子需要注意的細節問題。

As the name suggests, ultrasonic cleaning equipment is the cleaning equipment that uses ultrasonic to work, and the vibrator in ultrasonic is very important to the cleaning effect, so Xiaobian wants to explain the details that should be paid attention to when installing the vibrator of ultrasonic cleaning equipment.

1.安裝全系列超聲波清洗設備的振子需要提前準備好這些工具：氬弧焊、十號內六角扳手、鉻鐵錫線、2.5平方高溫線、2×2.5電纜線適量、振子膠、以及一些可能用到的剝線鉗、套管、扎帶、噴砂機、管件等。。

1. The vibrator for installing a full range of ultrasonic cleaning equipment needs to be prepared in advance: argon arc welding, No. 10 Allen wrench, chromium iron tin wire, 2.5 square high temperature wire, 2 × 2.5 proper amount of cable, vibrator glue, and some possible wire strippers, sleeves, ties, sandblasting machines, pipe fittings, etc..

2.全系列超聲波清洗設備的焊接螺釘需要根據振子的排布位置進行焊接，而且在焊接之前需要將其周圍清理干凈，以免影響振子的安裝。

2. The welding screws of the whole series of ultrasonic cleaning equipment need to be welded according to the arrangement position of the vibrator, and the surroundings need to be cleaned before welding to avoid affecting the installation of the vibrator.

3.安裝全系列超聲波清洗設備的時候需要按照使用要求進行膠水的配置，而且在安裝振頭時需將其均勻涂抹在超聲波振子底部，然后輕輕擰動將全系列超聲波振子的換能器底部和缸底接觸之間多余的空氣和膠水?dāng)D壓出來，讓振子和不銹鋼緊密結合為一個整體。

3. When installing the whole series of ultrasonic cleaning equipment, the glue shall be configured according to the use requirements, and when installing the vibrator, it shall be evenly applied to the bottom of the ultrasonic vibrator, and then gently screw it to squeeze out the excess air and glue between the bottom of the transducer and the bottom of the cylinder of the whole series of ultrasonic vibrator, so that the vibrator and stainless steel are closely combined as a whole.

4.將安裝好的全系列超聲波清洗設備的振子放在室溫相對高點的地方固化，然后在24小時后進行通電試機。

4. Place the vibrator of the installed full series of ultrasonic cleaning equipment at the relatively high point of room temperature for curing, and then conduct power on test after 24 hours.

上一篇：超聲波鋁蓋清洗機的使用方法
下一篇：高壓清洗機高壓膠管搭配選擇要注意什么？