歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-常見問題

常見問題

液壓件超聲波清洗機的功率選擇要注意什么？

作者：創始人來源：http://www.zhuohengsh.com/時間：2024-06-06

1.輸出功率越高，清洗效果越好，但正確合理的選擇超聲波輸出液壓件，超聲波清洗機的超聲波清洗效果與（輸出x清洗時間）成正比，在輸出功率較低的情況下，需要一定的時間去除污垢。當功率達到此值時，可以立即清除污垢。如果選擇功率過大，空化強度會大大提高，清洗效果也會提高，但即使在更精密的零件上，也會出現腐蝕點，所以損失不值得。另外，液壓件超聲波清洗機清洗槽底部的振動板存在嚴重的汽蝕現象，增加了水斑腐蝕。使用有機溶劑，如三氯乙烯，基本上是好的。振動板表面損傷時，空化腐蝕越嚴重，受力越大。因此，有必要根據實際應用情況選擇超聲輸出。

1. The higher the output power, the better the cleaning effect, but the correct and reasonable selection of ultrasonic output hydraulic components. The ultrasonic cleaning effect of the ultrasonic cleaning machine is directly proportional to the (output x cleaning time). In the case of lower output power, a certain amount of time is required to remove dirt. When the power reaches this value, dirt can be immediately removed. If the power is too high, the cavitation intensity will be greatly improved, and the cleaning effect will also be improved. However, even on more precise parts, corrosion points will appear, so the loss is not worth it. In addition, there is severe cavitation on the vibration plate at the bottom of the cleaning tank of the hydraulic component ultrasonic cleaning machine, which increases water spot corrosion. Using organic solvents, such as trichloroethylene, is generally good. When the surface of the vibrating plate is damaged, the more severe the cavitation corrosion, the greater the stress. Therefore, it is necessary to choose ultrasound output based on actual application situations.

2.液壓件超聲清洗機的輸出功率、空化閾值和頻率的選擇與輸出功率的選擇密切相關。頻率越高，空化閾值越高。換言之，頻率越低，空化現象越容易發生。在低頻條件下，液體壓縮變稀的時間間隔越長。在氣泡破裂之前，空腔的強度隨著氣泡體積的增大而增大。它有助于清潔。頻率約為40KHz，聲強相同，產生的空化氣泡多于20kHz，穿透力強。適用于表面形狀復雜的工件和擋塊的清洗。空化噪聲小，但空氣的化學強度低。適用于清洗臟污和粘結強度弱的清洗零件

The selection of output power, cavitation threshold, and frequency of hydraulic ultrasonic cleaning machine is closely related to the selection of output power. The higher the frequency, the higher the cavitation threshold. In other words, the lower the frequency, the easier it is for cavitation to occur. Under low-frequency conditions, the longer the time interval between liquid compression and thinning. Before the bubble ruptures, the strength of the cavity increases with the increase of bubble volume. It helps with cleaning. The frequency is about 40kHz, with the same sound intensity, producing more cavitation bubbles than 20kHz and strong penetration. Suitable for cleaning workpieces and stoppers with complex surface shapes. Cavitation noise is low, but the chemical intensity of the air is low. Suitable for cleaning dirty and weakly bonded parts

3.液壓件超聲波清洗機的功率輸出公式為

The power output formula of the hydraulic component ultrasonic cleaning machine is

（1），由換能器（俗稱振動頭）計算得出。目前市場上有兩種逆變器輸出：50W1pcs和60WPCs。液壓件超聲波清洗機功率：換能器個數n× 50W或n× 知道水槽的長度和寬度就足夠了。振動器與振動器之間的距離為100毫米

(1) , calculated by a transducer (commonly known as a vibrating head). There are currently two types of inverter outputs on the market: 50W1pcs and 60WPCs. Hydraulic component ultrasonic cleaning machine power: The number of transducers n x 50W or n x is sufficient to know the length and width of the water tank. The distance between the vibrator and the vibrator is 100 millimeters

（3）振動器的輸出功率通常為50瓦或60瓦。儲罐通常放置在600 x 400 mm表面的底部。通常，24個振動器是均勻分布的。如果污染嚴重，可以適當提高產量，使之均勻。28歲時，總功率約1400W，發電機功率1500W

(3) The output power of a vibrator is usually 50 watts or 60 watts. Storage tanks are typically placed at the bottom of a 600 x 400 mm surface. Usually, 24 vibrators are evenly distributed. If the pollution is severe, the production can be increased appropriately to make it even. At the age of 28, the total power is about 1400W, and the generator power is 1500W

（4）振動器停機時，液壓件超聲波清洗機的輸出功率為60x40x0和55x1320w

(4) When the vibrator stops, the output power of the hydraulic component ultrasonic cleaning machine is 60x40x0 and 55x1320w

超聲空化閾值與頻率密切相關。頻率越高，空化閾值越高。頻率越低，空化閾值越低，空化越容易發生。教你選擇液壓零件超聲波清洗機的功率。看完后就會知道，當工件表面較大或有污垢或工作表面附著力較高時，通常采用低頻超聲波清洗。高頻超聲波適用于某些精密零件的清洗。考慮到超聲波清洗的效果和經濟性，頻率一般為20-130khz。

The threshold of ultrasonic cavitation is closely related to frequency. The higher the frequency, the higher the cavitation threshold. The lower the frequency, the lower the cavitation threshold, and the more likely cavitation is to occur. Teach you how to choose the power of the ultrasonic cleaning machine for hydraulic components. After reading it, you will know that when the surface of the workpiece is large or there is dirt or high adhesion on the working surface, low-frequency ultrasonic cleaning is usually used. High frequency ultrasound is suitable for cleaning certain precision parts. Considering the effectiveness and economy of ultrasonic cleaning, the frequency is generally 20-130 kHz.

上一篇：通過式噴淋清洗機在使用時，需注意哪些事項？
下一篇：碳氫清洗機功能與工藝特性