歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-常見問題

常見問題

通過式清洗機如何又安全又高能效的操作？

作者：admin來源：http://www.zhuohengsh.com/時間：2023-03-10

通過式清洗機用于沖洗過濾液壓體系在制作、裝配、使用過程及保護時生成或侵入的污染物;也能夠適用于對作業油液的定期保護過濾，提高清潔度，防止或削減因污染而形成的故障，然后保證液壓體系設備的高性能、高可靠度和長壽命。下面來講下它的正確的安全的操作事項吧。

The pass-through cleaner is used to wash the pollutants generated or intruded during the production, assembly, use and protection of the filtration hydraulic system; It can also be applied to the regular protection and filtration of the operating oil, improve the cleanliness, prevent or reduce the failure caused by pollution, and then ensure the high performance, high reliability and long life of the hydraulic system equipment. Let's talk about its correct and safe operation.

檢查事項

Inspection items

a、查看管路體系有無漏氣漏水的狀況，如有這種狀況，應告訴維修人員修理。

A. Check whether the pipeline system has air and water leakage. If so, tell the maintenance personnel to repair it.

b、查看清洗液是否足夠，如果不行，及時添加清洗液。

B. Check whether the cleaning solution is sufficient. If not, add the cleaning solution in time.

c、先點動試車，然后空作業2-3分鐘，查看傳動體系(電動機、聯軸節、減速器)和運送帶的運動是否平穩，確認一切正常后，方可進行出產。

C. First jog the test run, and then idle for 2-3 minutes to check whether the drive system (motor, coupling, reducer) and the conveyor belt are moving smoothly, and confirm that everything is normal before production.

d、開啟浮油掃除設備(不帶浮油掃除設備在外)開始浮油掃除，因此時水泵尚開啟，水面安靜，排油作用好，待浮油根本掃除后停止除油，排油污多克利用午休時刻進行。

D. Start the oil slick cleaning equipment (without the oil slick cleaning equipment) to start the oil slick cleaning. Therefore, the water pump is still on, the water surface is quiet, and the oil drainage function is good. After the oil slick is completely cleaned, stop the oil removal. The oil pollution drainage can be carried out at noon break.
通過式清洗機

操作事項

Operating matters

a、被清洗的零件要整齊地放在運送帶上，不許壓在滾輪上;

A. The cleaned parts shall be neatly placed on the conveyor belt and shall not be pressed on the roller;

b、在運送帶上，被清洗的零件不能堆得過多，以免影響清洗作用。

B. On the conveyor belt, the cleaned parts should not be piled too much to avoid affecting the cleaning effect.

c、作業后，被清洗的零件不能停放在運送帶上，按停止按鈕，使全機停止運行。

C. After operation, the cleaned parts cannot be parked on the conveyor belt. Press the stop button to stop the whole machine.

d、清洗液應定期添加水和一定份額的金屬清洗劑以補充耗費，使液面保持在一定高度，如果清洗作用達不到規則的工藝要求時，應悉數更換清洗液。

D. The cleaning fluid shall be regularly added with water and a certain amount of metal cleaning agent to supplement the consumption, so as to keep the liquid level at a certain height. If the cleaning effect fails to meet the regular process requirements, the cleaning fluid shall be completely replaced.

注意，選購通過式清洗機時，如果想要有正確選擇的話，是需要做到以下這兩點，一是產品在選購前要做一些準備工作，而且是要認真對待和進行，好做到心中有數，二是進行產品選購時，要將其所有相關因素進行全面和綜合考慮，這樣可避免在考慮過程中出現問題，進而，影響到選購者的準確判斷和正確選擇。更多相關事項就來聯系我們http://www.zhuohengsh.com吧！

Note that if you want to make a correct choice when purchasing a walk-through cleaner, you need to do the following two things: first, you should do some preparatory work before purchasing the product, and you should take it seriously and carry it out so that you can have a good idea; second, you should take all relevant factors into consideration when purchasing the product, so that you can avoid problems in the process of consideration, and then, It affects the accurate judgment and correct choice of the buyer. Contact us for more relevant matters http://www.zhuohengsh.com Come on!

上一篇：碳氫清洗機設備優于傳統清洗模式的之處！
下一篇：超聲波清洗機能清洗鍵盤嗎？